View 42PX3RVA_6946164.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

plasma tv service manual caution before servicing the chassis, read the safety precautions in this manual. chassis : mf-056c model : 42PX3RVA 42PX3RVA-zc website:http://biz.lgservice.com e-mail:http://www.lgeservice.com/techsup.html pr vol menu tv/av ok www.datasheet.net/ datasheet pdf - http://www..co.kr/
contents safety precautions ...................................................................................3 description of controls .........................................................................4 specifications ...............................................................................................9 adjustment instructions ......................................................................11 trouble shooting guide ..........................................................................15 block diagram .............................................................................................24 exploded view ..............................................................................................26 exploded view parts list ........................................................................27 replacement parts list...........................................................................28 schematic diagram ........................................................................................ printed circuit board .................................................................................. www.datasheet.net/ datasheet pdf - http://www..co.kr/
safety precautions many electrical and mechanical parts in this chassis have special safety-related characteristics. these parts are identified by in the schematic diagram and replacement parts list. it is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent x-radiation, shock, fire, or other hazards. do not modify the original design without permission of manufacturer. general guidance an isolation transformer should always be used during the servicing of a receiver whose chassis is not isolated from the ac power line. use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. it will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. if any fuse (or fusible resistor) in this monitor is blown, replace it with the specified. when replacing a high wattage resistor (oxide metal film resistor, over 1w), keep the resistor 10mm away from pcb. keep wires away from high voltage or high temperature parts. due to high vacuum and large surface area of picture tube, extreme care should be used in handling the picture tube . do not lift the picture tube by it's neck. leakage current cold check(antenna cold check) with the instrument ac plug removed from ac source, connect an electrical jumper across the two ac plug prongs. place the ac switch in the on position, connect one lead of ohm-meter to the ac plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. if the exposed metallic part has a return path to the chassis, the measured resistance should be between 1m? and 5.2m?. when the exposed metal has no return path to the chassis the reading must be infinite. an other abnormality exists that must be corrected before the receiver is returned to the customer. leakage current hot check (see below figure) plug the ac cord directly into the ac outlet. do not use a line isolation transformer during this check. connect 1.5k/10watt resistor in parallel with a 0.15uf capacitor between a known good earth ground (water pipe, conduit, etc.) and the exposed metallic parts. measure the ac voltage across the resistor using ac voltmeter with 1000 ohms/volt or more sensitivity. reverse plug the ac cord into the ac outlet and repeat ac voltage measurements for each exposed metallic part. any voltage measured must not exceed 0.75 volt rms which is corresponds to 0.5ma. in case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer. leakage current hot check circuit 1.5 kohm/10w to instrument's exposed metallic parts good earth ground such as water pipe, conduit etc. ac volt-meter important safety notice 0.15uf www.datasheet.net/ datasheet pdf - http://www..co.kr/
remote control key functions remote control key functions - when using the remote control aim it at the remote control sensor of the set. - there's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature. power mute tv/av i/ii list pr pr vol ok 123 456 789 psm ssm 0 vol arc menu q.view text sleep time mix hold reveal index mode ? i m multimedia size update multimedia selects the component, rgb or hdmi modes. switches the set on from standby. power switches the set on from standby or off to standby. arc changes the picture format. menu displays on screen menus one by one. exits the current menu. memorizes menu changes. q.view returns to the previously viewed pro- gramme. note : this function works only when favourite programme is set to off . otherwise each press of this button will select a stored favorite pro- gramme. ssm to select the sound appropriate to your viewing programme character. number buttons sleep sets the sleep timer. i / ii selects the language during dual lan- guage broadcast. selects the sound output. text these buttons are used for teletext. for further details, see the ?eletext section. coloured buttons these buttons are used for teletext (only teletext models) or programme edit. list displays the programme table. tv/av selects the tv, av, component, rgb or hdmi modes. switches the set on from standby. mute switches the sound on or off. d d / e e (programme up/down) selects a programme or a menu item. switches the set on from standby. f f / g g (volume up/down) adjusts the volume. adjusts menu settings. ok accepts your selection or displays the current mode. psm adjusts the factory preset picture according to the room. description of controls www.datasheet.net/ datasheet pdf - http://www..co.kr/
location and function of controls location and function of controls pr vol menu tv/av ok pr vol menu tv/av ok 1 3 2 4 5 6 7 1. remote control sensor 2. power indicator illuminates red in standby mode, illuminates green when the set is turned on. 3. power button switches the set on from standby or off to standby. 4. tv/av button selects the tv, av, component, rgb or hdmi modes. switches the set on from standby. 5. menu displays on screen menus one by one. exits the current menu. memorizes menu changes. 6. ok accepts your selection or displays the current mode. 7. d d / e e (programme up/down) selects a programme or a menu item. switches the set on from standby. f f / g g (volume up/down) adjusts the volume. adjusts menu settings. www.datasheet.net/ datasheet pdf - http://www..co.kr/
location and function of controls location and function of controls s-video video audio r l/mono a v5 v5 ac input rs-232c input (control/service) antenna remote control hdmi audio input rgb input (mono) (mono) component component l r audio audio l r audio audio a v4 v4 v v ariable ariable audio out audio out a v1 a v2 a v3 s-video s-video video video l r audio audio 1. hdmi(dvi video) / audio input / rgb input connect the monitor output socket of the personal com- puter, dvd or stb to this socket. note: if you want to use rgb/dvi audio, we strongly recom- mend that you use the cable that has a core, or the emi filter core along with separate cable. 2. control lock / remote control 3. rs-232c input(control/service) port connect to the rs-232c port on a pc. 4. component input connect dvd video outputs to y, p b , p r of component input and audio outputs to audio sockets of audio input. audio/video in sockets (av4) connect the audio/video out sockets of external equipment to these sockets. s-video/audio in sockets connect the s-video out socket of an vcr to the s-video socket. connect the audio out sockets of the vcr to the audio sock- ets as in av4 . 5. variable audio output 6. euro scart socket connect the euro scart socket of the vcr to these sockets. note: if you want to use the euro scart cable, you have to use the signal shielded euro scart cable. 7. antenna input 8. power cord socket this set operates on an ac power. the voltage is indicated on the specifications page. never attempt to operate the set on dc power. 9. audio/video input (av5) s-video/audio in sockets 1 4 2 3 6 7 5 8 9 - shown is a simplified representation of the set. - here shown may be somewhat different from your set. www.datasheet.net/ datasheet pdf - http://www..co.kr/
displayable monitor specification displayable monitor specification rgb / hdmi mode resolution 640x350 720x400 640x480 848x480 800x600 horizontal frequency(khz) vertical frequency(hz) 852x480 832x624 1024x768 1152x864 1152x870 1280x960 1280x1024 70.09 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.05 70.01 75.00 75.06 60.02 60.02 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 31.500 37.799 39.375 31.500 37.799 39.375 35.156 37.879 48.077 46.875 53.674 49.725 48.363 56.476 60.023 68.677 54.348 63.995 67.500 68.681 60.023 63.981 rgb / hdmi mode 50px3r series 42px3rv series resolution 640x350 720x400 640x480 848x480 800x600 horizontal frequency(khz) vertical frequency(hz) 852x480 832x624 1024x768 1360x768 1366x768 1152x864 1152x870 1280x960 1280x768 1280x1024 70.09 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 (rgb) 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.00 75.02 85.00 60.00 75.02 85.00 60.05 70.01 75.00 85.00 75.06 60.00 75.00 85.00 60.02 60.02 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 31.500 37.799 39.375 31.500 37.799 39.375 35.156 37.879 48.077 46.875 53.674 49.725 48.363 56.476 60.023 68.677 47.700 59.625 68.500 47.700 59.625 69.500 54.348 63.995 67.500 77.487 68.681 47.693 60.091 68.504 60.023 63.981 www.datasheet.net/ datasheet pdf - http://www..co.kr/
a s m a r k lg tv owners manual 1.5v 1.5v alkaline batteries power cord power mute tv/av i/ii list pr pr vol ok 123 456 789 psm ssm 0 vol arc menu q.view text sleep time mix hold reveal index mode ? i m multimedia size update remote control handset - optional extras can be changed or modified for quality improvement without any notification new optional extras can be added. - contract your dealer for buying these items. optional extras accessories accessories tilt wall mounting bracket video cables audio cables ceiling mounting bracket 4 0 4 2 5 0 42 40 - secure the set assembly by joinning it to a wall by using the eye bolts/wall brackets. joinning the set assembly to the wall to protect the set tumbling after the set must be mounted on a desktop, install the eye bolts on the set as shown. insert the 2 eye bolts and tighten securely, in the holes on the bracket. install the wall brackets on the wall with 2 bolts, (not supplied with the product), as shown. match the height of the eye bolts and the wall brackets. check to be sure the brackets are tightened securely. ?secure the set assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown. 2-wall brackets 2-eye bolts www.datasheet.net/ datasheet pdf - http://www..co.kr/
specifications note : specifications and others are subject to change without notice for improvement . v application range this spec is applied to the 42?dp tv used mf-056c chassis. v specification each part is tested as below without special appointment. 1) temperature : 255? (779?), cst : 405 2) relative humidity: 65 10% 3) power voltage: standard input voltage (100-240v~, 50/60hz) * standard voltage of each product is marked by models. 4) specification and performance of each parts are followed each drawing and specification by part number in accordance with bom. 5) the receiver must be operated for about 20 minutes prior to the adjustment . v test method 1) performance : lge tv test method followed. 2) demanded other specification safety: ce, iec specification emc : ce, iec v general specification 1. general specification remark safety : iec/en60065, emi : en55013, ems : en55020 model name 42PX3RVA-zc market eu remark pdp lge spec maker : sony/ sanken specification 42 inch wide color display module 16:9 pdp42v7xxxx rgb closed type, film filter 1) temp : 0~40 deg 2) humidity : 0~85% 1) temp : -20~60 deg 2) humidity : 0~85% 100-240v~, 50/60hz no 1 2 3 4 5 6 item display screen device aspect ratio pdp module operating environment storage environment input voltage www.datasheet.net/ datasheet pdf - http://www..co.kr/
2. model specification( 42PX3RVA-za) item market broadcasting system available channel receiving system scart jack(3ea) video input(2ea) s-video input(2ea) component input(2ea) rgb input(1ea) hdmi input(1ea) audio input(4ea) audio output(1ea) wired control no 1 2 3 4 5 6 7 8 9 10 11 12 13 specification eu pal b/g/i/d/k, secam l/l brand pal secam vhf/uhf c1~c69 catv s1~s47 upper heterodyne pal, secam pal, secam, ntsc pal, secam, ntsc y/cb/cr, y/pb/pr rgb-pc rgb-dtv hdmi-pc hdmi-dtv pc audio(1ea), component, av(2ea) variable audio out discrete ir remark 4 system : pal, secam, ntsc,pal60 4 system : pal, secam, ntsc,pal60 l/r input l/r output www.datasheet.net/ datasheet pdf - http://www..co.kr/
adjustment instructions 1. application object these instructions apply to the mf-056c chassis. 2. specification (1) because this is not a hot chassis, it is not necessary to use an isolation transformer. however, the use of isolation transformer will help protect test instrument. (2) adjustment must be done in the correct order. (3) the adjustment must be performed in the circumstance of 255? of temperature and 6510% of relative humidity if there is no specific designation. (4) the input voltage of the receiver must keep 100-220v, 50/60hz. (5) the receiver must be operated for about 15 minutes prior to the adjustment. o after rgb full white heat-run mode, the receiver must be operated prior to adjustment. o enter into heat-run mode 1) press the power on key on r/c for adjustment. 2) osd display and screen display 100% full white pattern. [ set is activated heat-run without signal generator in this mode. [ single color pattern(red/blue/green) of heat-run mode uses to check panel. caution) if you turn on a still screen more than 20 minutes (especially digital pattern, cross hatch pattern), after image may be occur in the black level part of the screen. 3. channel memory 3-1. setting up the lgids 1) install the lgids. (idsinst.exe) 2) after installation, restart your pc. 3) extract [files.zip] to folder [c:\lgids\files]. 4) start lgids. 3-2. channel memory method 1) select ?dp?and ?urricane?on model dialog. and check your connection in communication dialog. (if your connection is ?g? then set your port(com1,2,3,...) correctly.) 2) connect rs-232c cable and turn on the power. (if your connection has completed, you can see ?eady?) [ if your set is not an end products but only a board, you have to make your board to stand-by state (led_r). and you have to download in stand_by power state. 3) select proper ch_memory file(*.nvm) for each model at [nvram download] $ [write batch] next, select proper binary file(*.bin) including the ch information for each model at [nvram file]. 4) click the [download] button. it means the completion of the ch memory download if all items show ?k?and status is changed by ?ass?at the lower right corner of the window. 5) if you want to check whether the ch information is memorized correctly or not, click the [verify] button. and then compare nvram file(*.bin) with the ch information downloaded. (fig. 1) (fig. 2) (fig. 3) www.datasheet.net/ datasheet pdf - http://www..co.kr/
4. power pcb assy voltage adjustments (va, vs voltage adjustments) 4-1. test equipment : d.m.m. 1ea 4-2. adjustment method [p/no 3501v00220a(sanken) b/d, p/no 6709v00010a(lgit) b/d] (1) va adjustment 1) after receiving 100% full white pattern, heat run. 2) connect + terminal of d.m.m to va pin of p807, connect - terminal to gnd pin of p807. 3) after turning rv501, voltage of d.m.m adjustment as same as va voltage which on label of panel right/top. (deviation; 0.5v) (2) vs adjustment 1) connect + terminal of d.m.m to vs pin of p807, connect ?terminal to gnd pin of p807. 2) after turning rv401, voltage of d.m.m adjustment as same as va voltage which on label of panel right/top. (deviation; 0.5v) 5. edid (the extended display identification data)/ ddc (display data channel) download 5-1. required test equipment 1) adjusting pc with s/w for writing edid data.(s/w : edid tester ver.2.5) 2) a jig for edid download 3) cable : serial(9pin or usb) to d-sub 15pin cable, d-sub 15pin cable, dvi to hdmi cable. 5-2. setting of device 5.3. preparation for adjustment 1) as above fig. 5, connect the set, edid download jig, pc & cable. 2) turn on the pc & edid download jig. and execute the s/w : edid tester ver,2.5 3) set up s/w option repeat number : 5 device address : a0 pagebyte : 8 4) power on the set 5.4. sequence of adjustment (1) ddc data of analog-rgb 1) init the data 2) load the edid data.(open file) [analog-rgb : type_vga.ana] [digital(hdmi) : type_vga.dvi] 3) set the s/w as below. 4) push the ?rite data & verify?utton. and confirm ?es? 5) if the writing is finished, you will see the ?k?message. each pcb assembly must be checked by check jig set. (because power pcb assembly damages to pdp module, especially be careful) (fig. 4) connection diagram of power adjustment for measuring (fig. 5) connection diagram of ddc download www.datasheet.net/ datasheet pdf - http://www..co.kr/
6. auto av(cvbs) color balance 6-1. requirement - this av color balance adjustment should be per formed before white balance adjustment. 6-2. required equipme 1) remote controller for agdjustment 2) av pattern generator : 802f pattern generator, master (mspg-925fa), etc (which has pal composite video format output with standard (1.0 vpp) vertical 100% color bar pattern as fig.6) 6-3 method of auto rgb color balance 1) input the pal composite video (fig.6.100% color bar pattern) into video input. (rz-42px30 : av4/av5 input 50hz) 2) set the psm to standard mode in picture menu. 3) press instart key on r/c for adjustment. 4) press the g (vol. +) key operat to set, then it becomes automatically. 5) auto-rgb ok means completed adjustment. 7. adjustment of white balance 7-1. required equipment 1) remote controller for adjustment 2) color analyzer (ca-100 or same product) 3) auto w/b adjustment instrument(only for auto adjustment) 4) av pattern generator 7-2. connecting diagram of equipment for measuring (for auto adjustment) w auto adjustment map(rs-232c) 7-3. adjustment of white balance o operate the zero-calibration of the ca-100, then stick sensor to pdp module surface when you adjust. o for manual adjustment, it is also possible by the following sequence. 1) select white pattern of heat-run mode by pressing power on key on remote control for adjustment then operate heat run more than 15 minutes. 2) as below fig.7, supply window or gray step pattern to video input (rz-42px30 : av4/av5 input 50hz) 3) press the tv/av key on r/c for converting input mode. 4) set the psm to standard mode in picture menu. 5) enter the white balance adjustment mode by pressing the instart key twice(white balance) on r/c 6) stick sensor to center of the screen and select each items (red/green/blue gain and offset) using d / e (ch +/-) key on r/c. 7) adjust high light with r gain/ b gain and low light with g offset/ b offset using f / g (vol +/-) key on r/c. 8) adjust it until color coordination becomes as below. (g gain:7a/ r offset:7f/ g offset:7e/ b offset:80 is fixed) [mf-056c : rz-42px30] - vga 42 bright : high light : 60 20 cd/m2 color-coordinate : high light : x : 0.285 0.003 y : 0.290 0.003 color temperature : 9,300? 500? 9) when adjustment is completed, exit adjustment mode using exit key on r/c (fig. 7) connection diagram of auto w/b adjustment mspg-2100 / mstg-5200 216 level (85 ire) color analyzer type ; ca-100 cvbs signal input rs-232c serial communication (fig. 8) position and pattern for manual adjustment of white balance 216 level (85 ire) type baud rate 115200 index r gain g gain b gain r offset g offset b offset data bit 8 cmd1 cmd2 ja jb jc jd je jf stop bit 1 parity none mf-056c : rz-42px30 protocol setting data min value 00(00) 00(00) 00(00) 00(00) 00(00) 00(00) max value 255(ff) 255(ff) 255(ff) 255(ff) 255(ff) 255(ff) rs232 (fig. 6) auto av(cvbs) color balance test pattern www.datasheet.net/ datasheet pdf - http://www..co.kr/
8. auto component color balance 8-1. required test equipment 1) remote controller for adjustment 2) 802f pattern generator (which has 720p ypbpr output & pc 1024x768 60hz with standard(0.7vpp) vertical 100% color bar pattern as fig.8) 8-2. method of auto component color balance 1) input the component 720p 100% color bar signal into component1 or component2. 2) set the psm to standard mode in picture menu. 3) press instart key on r/c for adjustment. 4) press the g (vol. +) key operate to set, then it becomes automatically. 5) auto-rgb ok means complete adjustment 9. auto rgb color balance 9-1. required test equipment 1) remote controller for adjustment 2) 802f pattern generator, master (mspg-925fa), etc. (which has xga 60hz pc format output with standard (0.7vpp) horizontal black and white pattern as fig.10) 9-2. method of auto rgb color balance 1) input the pc 1024x768 60hz horizontal black and white pattern into rgb. 2) set the psm to standard mode in picture menu. 3) press adj key on r/c for adjustment. 4) press the g (vol. +) key operate to set, then it becomes automatically. 5) auto-rgb ok means completed adjustment. 10. default value in adjustment mode 10-1. auto color balance(component/rgb) 10-2. white balance level : 0 level : 255 (fig. 10) auto rgb color balance test pattern (fig. 11) default value on osd (fig. 12) default value on osd auto color balance(hex) auto-rgb g to set red offset1 22 green offset1 24 blue offset1 23 red offset2 45 green offset2 43 blue offset2 37 red gain 14 green gain 31 blue gain 11 reset g to set white balance(hex) red gain 82 red offset 7a green gain 86 green offset 7f blue gain 7e blue offset 80 reset g to set (fig. 9) auto component color balance test pattern www.datasheet.net/ datasheet pdf - http://www..co.kr/
trouble shooting guide 1. power board 1-1. the whole flowchart which it follows in voltage output state start check manufacture enterprise meaning of a passage 1. check the power off condition. doesn't the screen whole come out? it is identical with power off condition? yes yes no no no no no 2. check the interface signal condition. is the interface signal operated? yes 3. check the st-by 5v signal circuit. doesn't the low pressure output come out? doesn't the st-by 5v signal come out? yes yes no 4. check the 5v monitor signal circuit. doesn't the 5v monitor signal come out? yes 7. check the vsc vs-on signal doesn't the high tension output come out? doesn't the vsc signal vs-on come out? yes yes high tension output voltage drop it occurs? when remove the y b/d module input connector, output voltage drop it occurs? when remove the y, z b/d module input connector, power board high tension output voltage drop it occurs? yes no no 9. check the power board output high tension circuit yes 10. check the z b/d module output circuit yes when remove the z b/d module input connector, output voltage drop it occurs? 11. check the y b/d module output circuit yes no 8. check the vs, va voltage output circuit. doesn't the vs, va voltage output come out? yes no no 5. check the vsc rl-on signal. doesn't the vsc signal rl-on come out? yes 6. check the vsc low pressure output doesn't the vsc low pressure output come out? yes www.datasheet.net/ datasheet pdf - http://www..co.kr/
1-2. sony power board structure 1 2 3 t502: vs trans t702: va trans t101: st-by trans t103: low voltage trans www.datasheet.net/ datasheet pdf - http://www..co.kr/
1-3. sanken power board structure 1 2 3 t221: vs trans t271: va trans t121: st-by trans t201: low voltage trans www.datasheet.net/ datasheet pdf - http://www..co.kr/
2. no power (1) symptom ? does? minute discharge at module. ? non does not come in into the front led. (2) check follow is plug in power cord? plug in power cord. yes no is connect the line filter and power board cable? connect cable. yes no is normal the fuse(f101) on power board? replace fuse. yes no is connect the power board and 7p of vsc board cable? connect cable. yes no after remove the cable connect to power board(except the cn101 connection cable), authorizes the ac voltage marking on manual. when st-by 5v does not operate, replace power board. www.datasheet.net/ datasheet pdf - http://www..co.kr/
3. protect mode (1) symptom ? after once shining, it does not discharge minutely from module ? the rely falls(the sound is audible ?lick? ? it is converted with the color where the front led is red from green. (2) check follow is normal the power board? replace power board. is output the normality low/high voltage except stand-by 5v? yes no no is normal the each connector? replace connector. replace y-board. after connecting well each connector, the normality it operates? yes no no is normal the ctrl board? replace x-board. is normal the output voltage after remove p1, 2, 4, 9, 10 connector of ctrl-b/d? yes no yes is normal the y- board? is normal the output voltage after remove p5, p6 connector of y-b/d? is normal the fuse(fs2) on y-b/d? (in case of open is replace) yes no yes yes replace z-board. is normal the z- board? is normal the output voltage after remove p1 connector of z-b/d? is normal the fuse(fs1, fs2) on z- b/d? (in case of open is replace) yes no yes is normal the x- board? is normal the output voltage after remove p1, 2, 3, 4, 5 connector of x-b/d? after remove p1, p2, p3 output voltage normality: replace right x-b/d after remove p4, p5 output voltage normality: replace left x-b/d yes no yes is normal the vsc board? is normal the output voltage after remove p1001, p1100? after crisis cof of each board, check the normality operates. if in case normality operates, correspondence cof fail is replace the module. after remove p1001, 1100 normal operation: replace vsc board yes no is normal the cof of x, y, z? no yes yes www.datasheet.net/ datasheet pdf - http://www..co.kr/
4. no raster (1) symptom ? does? minute discharge at module. ? it maintains the condition where the front led is green. (2) check follow is normal the power board? replace power board. is output the normality low/high voltage except stand-by 5v? yes no no is normal the each connector? replace connector. replace y-board. after connecting well each connector, the normality it operates? yes no no is normal the ctrl board? replace x-board. is normal the output voltage after remove p1, 2, 4, 9, 10 connector of ctrl-b/d? yes no yes is normal the y- board? is normal the output voltage after remove p5, p6 connector of y-b/d? is normal the fuse(fs2) on y-b/d? (in case of open is replace) yes no yes yes replace z-board. is normal the z- board? is normal the output voltage after remove p1 connector of z-b/d? is normal the fuse(fs1, fs2) on z- b/d? (in case of open is replace) yes no yes is normal the x- board? is normal the output voltage after remove p1, 2, 3, 4, 5 connector of x-b/d? after remove p1, p2, p3 output voltage normality: replace right x-b/d after remove p4, p5 output voltage normality: replace left x-b/d yes no yes is normal the vsc board? is normal the output voltage after remove p1001, p1100? after crisis cof of each board, check the normality operates. if in case normality operates, correspondence cof fail is replace the module. after remove p1001, p1100 normal operation: replace vsc board yes no is normal the cof of x, y, z? no yes yes www.datasheet.net/ datasheet pdf - http://www..co.kr/
5. in case of occur strange screen into specific mode 5-1. in case of does? display the osd (1) symptom ? led is green ? the minute discharge continuously becomes accomplished from module (2) check follow is normal the lvds cable? is normal the vsc board? is the lvds cable connected well? cable inserts well. yes no no yes operates the fil8532 ic(ic800)? replace fil8532 ic(ic800). no is normal the ctrl board of module? replace ctrl b/d. no no yes replace vsc b/d replace cable. yes www.datasheet.net/ datasheet pdf - http://www..co.kr/
5-2. in case of does? display the screen into specific mode (1) symptom ? the screen does not become the display from specific input mode (rf, av, component, rgb, dvi). (2) check follow ? check the all input mode should become normality display . ? check the video(main)/data(sub), video(main)/video(sub) should become normality display from the pip mode or dw mode. (re-check it swap) (3) in case of becomes unusual display from rf mode (4) in the case of becomes unusual display from rf, av mode (5) in the case of becomes unusual display from component, rgb mode (6) in the case of becomes unusual display from hdmi mode is normal the tuner? is normal the cxa2069q? is the tuner cable connected well? cable inserts well. yes no no yes is normal the fil8532? replace tuner no is normal the input voltage, iic communication and cvbs output? yes is normal the input voltage, iic communication and hv sync? no replace ic no is normal the input voltage, iic communication and hv sync? no replace ic no is normal the cxa2069q? yes is normal the fil8532? is normal the input voltage, iic communication and hv sync? no replace ic no is normal the input voltage, iic communication and hv sync? no replace ic no is normal the fil8532? is normal the input voltage, iic communication and hv sync? no replace ic no is normal the sil9011? yes is normal the fil8532? is normal the input voltage, iic communication and hv sync? no replace ic no is normal the input voltage, iic communication and hv sync? no replace ic no www.datasheet.net/ datasheet pdf - http://www..co.kr/
6. in case of no sound (1) symptom ? led is green ? screen display but sound is not output (2) check follow is normal the spk cable? is the spk cable connected well? cable inserts well. no no replace ic400 no replace ic401 no replace spk cable yes yes is normal the rf/ av/ component/ rgb/ hdmi sound? no operates the ic400? operates the ic401? replace ic402 no operates the ic402? replace vsc b/d yes yes www.datasheet.net/ datasheet pdf - http://www..co.kr/
block diagram www.datasheet.net/ datasheet pdf - http://www..co.kr/
memo www.datasheet.net/ datasheet pdf - http://www..co.kr/
exploded view 300 301 304 302 202 206 203 204 201 205 580 410 530 121 601 600 120 501 401 400 303 207 200 520 430 590 www.datasheet.net/ datasheet pdf - http://www..co.kr/
120 6401vd0032a speaker assembly, full range(r) rz-42px30 film type 121 6401vd0033a speaker assembly, full range(l) rz-42px30 film type 200 6348q-e080w pdp, 42?852*480 pdp42v70102.adlgb 201 6871qch053a pwb(pcb) assembly,display ctrl assy hand insert 42v7 fpga 202 6871qdh084a pwb(pcb) assembly,display ydrv assy hand insert 42v7 ydrv top b/d 203 6871qdh085a pwb(pcb) assembly,display ydrv assy hand insert 42v7 ydrv btm b/d 204 6871qlh047a pwb(pcb) assembly,display xrlt assy hand insert 42v7 xl b/d 205 6871qrh055a pwb(pcb) assembly,display xrrt assy hand insert 42v7 xr b/d 206 6871qyh036a pwb(pcb) assembly,display ysus assy hand insert 42v7 207 6871qzh041a pwb(pcb) assembly,display zsus assy hand insert 42v7 zsus hand insert assy 300 3091v00816c cabinet assembly, rz-42px30 stereo mf056c film type skd 301 4980v01203b supporter, assy al filter top rz-42px30 c/skd 302 4980v01204b supporter, assy al filter bottom rz-42px30 c/skd 303 4980v01205b supporter, assy al filter right rz-42px30 c/skd 304 4980v01206b supporter, assy al filter left rz-42px30 c/skd 400 3809v00605b back cover assembly, 42px17/30 chassis change c/skd 401 3301v00085a plate assembly, assy 3300v00552a rz-42px30 plate tuner cover 410 4980v01071b supporter, assy al vertical rz-42px10 skd 430 3501v00216e board assembly, assy ap-42dx30 mf056c c/skd 501 3301v00083a plate assembly, assy 3300v00550a 3301v00084a 42px17/30 plate tuner 520 6871vmmf61a pwb(pcb) assembly,main mf-056c h2, rz-42px30 530 6871vsms36b pwb(pcb) assembly,sub cont mf056c rz-42px30 skd no vinyl 580 6709v00010a power supply assembly, pdp 42inch mf056a 350w ypsu-j006a lg innotek psu assy 600 6871vsms18b pwb(pcb) assembly,sub a/v mf056a rt/rz-42px40 side a/v susab 601 4811v00118a bracket assembly, deco rz-42px10 rf043b side av exploded view parts list no. part no. descriptions www.datasheet.net/ datasheet pdf - http://www..co.kr/
mic39100 3p sot223 r/tp ldo type 2.5v ba033fp-e2 rohm 3p-sop,to252-3 r/tp 3.3v ka7809r, fairchild 2p d-pak, r/tp ic sc156515m-1.8tr semtech 5p/to-263-5 r/tp ba033fp-e2 rohm 3p-sop,to252-3 r/tp 3.3v ba033fp-e2 rohm 3p-sop,to252-3 r/tp 3.3v ba033fp-e2 rohm 3p-sop,to252-3 r/tp 3.3v mic39100 micrel 3p sot223 r/tp ldo type sc156515m-1.8tr semtech 5p/to-263-5 kia78r05f kec 5pin dpak r/tp 1a,5v sc156515m-1.8tr semtech 5p/to-263-5 sii9011clu(pb free) silicon image 128p at24c02n-10si-2.7 atmel 8p soic r/tp mc34063adr2g on semi so-8p r/tp cxa2069q qfp64 bk i2c bus av s/w la7217m mfp14 tp sync separator ml-00ba msp4410k micronas 80p/pqfp nsp-2100a,lf neofidelity tqfp 64p tas5122dcar 56p/tssop r/tp 30w stereo ka4558d 8sop op amp 74hc14d 14sop tp shitter trigger at24c02n-10si-2.7 atmel 8p soic 74hc14d 14sop tp shitter trigger icl3232cbnz intersil 16p/sop r/tp fli8532bc-lf genesis 416p/pbga 24lc256-i/sm 8p,sop tp 256k iic serial at49bv160-70ti atmel 48p tsop k4d261638f-lc50,lf tsopii 66p k4d261638f-lc50,lf tsopii 66p bss83 tp philips n-channel s/w tr bss83 tp philips n-channel s/w tr bss83 tp philips n-channel s/w tr bss83 tp philips n-channel s/w tr bss83 tp philips n-channel s/w tr bss83 tp philips n-channel s/w tr chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec kra102s r/tp kec sot23 chip tr chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec replacement parts list loca. no part no description q202 q203 q204 q205 q206 q207 q300 q303 q304 q305 q400 q401 q402 q403 q404 q405 q406 q407 q408 q409 q410 q411 d1005 d1006 d1007 d1008 d1009 d1010 d1012 d1013 d102 d103 d104 d105 d106 d108 d1100 d1105 d1109 d112 d113 d114 d1200 d1201 d300 d500 d501 d502 d504 d505 d506 0tr387500aa 0tr150400ba 0tr150400ba 0tr387500aa 0tr150400ba 0tr150400ba 0tr387500aa 0tr387500aa 0tr387500aa 0tr150400ba 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr102008aa 0tr102008aa 0tr387500aa 0tr102008aa 0tr387500aa 0tr387500aa 0tr387500aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd200009af 0dd200009af 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dd184009aa 0ds113379ba 0dd226239aa 0dd226239aa 0dd226239aa 0dd226239aa 0dr050008aa 0dr050008aa 0dr050008aa chip 2sc3875s(aly) kec chip 2sa1504s(asy) kec chip 2sa1504s(asy) kec chip 2sc3875s(aly) kec chip 2sa1504s(asy) kec chip 2sa1504s(asy) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sa1504s(asy) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec kra102s r/tp kec sot23 chip tr kra102s r/tp kec sot23 chip tr chip 2sc3875s(aly) kec kra102s r/tp kec sot23 chip tr chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec chip 2sc3875s(aly) kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec ru2m v(1) tp sanken ru2m v(1) tp sanken kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec kds184 tp kec - 85v - 300ma 1ss133 t-72 tp rohm korea do34 90v kds226 tp kec kds226 tp kec kds226 tp kec kds226 tp kec sd05.tc r/tp semtech sod323 5v 5a 15a sd05.tc r/tp semtech sod323 5v 5a 15a sd05.tc r/tp semtech sod323 5v 5a 15a loca. no part no description ic1000 ic1001 ic1002 ic1003 ic1004 ic1005 ic1100 ic1101 ic1102 ic1103 ic1104 ic1200 ic1201 ic202 ic300 ic301 ic400 ic401 ic402 ic403 ic404 ic500 ic502 ic600 ic800 ic802 ic900 ic901 ic902 ic1202 ic1203 ic200 ic201 ic503 ic504 q100 q1000 q1001 q1002 q1003 q1004 q101 q101 q102 q102 q103 q104 q1200 q201 0iprpml001a 0imcrrh001a 0imcrfa010a 0ipmg00027a 0imcrrh001a 0imcrrh001a 0imcrrh001a 0iprpml001a 0ipmg00027a 0ipmgke030a 0ipmg00027a 0iprps5005a 0immral014b 0ipmgon013b 0iso206900a 0isa721700c 0imcrmn028b 0ilnr00015a 0imcrti028c 0iss455880a 0iph741400e 0immral014b 0iph741400e 0iprp00009a 0imcr02005a 0imp242560a 0immral016d 0immr00002a 0immr00002a 0tr830009ba 0tr830009ba 0tr830009ba 0tr830009ba 0tr830009ba 0tr830009ba 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr102008aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa 0tr387500aa ic transistor - 28 - diode www.datasheet.net/ datasheet pdf - http://www..co.kr/
- 29 - loca. no part no description zd100 zd101 zd107 zd300 zd301 zd400 zd600 c1000 c1005 c1007 c1009 c1010 c1019 c1022 c103 c1030 c1043 c1046 c1047 c1050 c1051 c1064 c1065 c1066 c1067 c1068 c1069 c1071 c1073 c108 c1082 c1083 c1084 c1085 c1087 c1098 c1099 c1102 c1105 c1107 c1108 c11 10 c11 15 c11 16 c11 17 c11 17 c11 18 c11 19 c1120 c1126 0dr050008aa 0dr050008aa 0dr050008aa 0dr050008aa 0dr050008aa 0dzrm00248a 0dr050008aa 0ce477sf6dc 0ce477sf6dc 0ce107sf6dc 0ce107sf6dc 0ce107sf6dc 0ce476sf6dc 0ce107sf6dc 0ce4763f618 0ce476sf6dc 0ce476sf6dc 0ce477sf6dc 0ce476sf6dc 0ce477sf6dc 0ce477sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce477sf6dc 0ce477sf6dc 0ce227sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce477sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce107sf6dc 0ce107sf6dc 0ce477sf6dc 0ce477dj618 0ce477sf6dc 0ce227sf6dc 0ce227vf6dc 0ce477sf6dc 0ce477dj618 0ce227vf6dc 0ce477sf6dc sd05.tc r/tp semtech sod323 5v 5a 15a sd05.tc r/tp semtech sod323 5v 5a 15a sd05.tc r/tp semtech sod323 5v 5a 15a sd05.tc r/tp semtech sod323 5v 5a 15a sd05.tc r/tp semtech sod323 5v 5a 15a rlz8.2b-te11 rohm r/tp llds(ll-34) sd05.tc r/tp semtech sod323 5v 5a 15a 470uf mvg 16v 20% r/tp(smd) smd 470uf mvg 16v 20% r/tp(smd) smd 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 47uf sre 16v m fl tp5 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 470uf mvg 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 470uf mvg 16v 20% r/tp(smd) smd 220uf mvg 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 470uf std 35v 20% fl tp 5 470uf mvg 16v 20% r/tp(smd) smd 220uf mvg 16v 20% r/tp(smd) smd 220uf mv 16v 20% r/tp(smd) smd 470uf mvg 16v 20% r/tp(smd) smd 470uf std 35v 20% fl tp 5 220uf mv 16v 20% r/tp(smd) smd 470uf mvg 16v 20% r/tp(smd) smd loca. no part no description c1135 c1136 c1137 c1138 c1148 c1154 c1 17 c1 18 c1185 c1 19 c1199 c120 c1200 c1201 c121 c1225 c1230 c1231 c1245 c1247 c129 c130 c130 c131 c1311 c1312 c1314 c1315 c1316 c1317 c1318 c135 c1406 c1414 c1415 c1419 c1420 c1424 c1425 c1428 c1438 c1441 c1506 c204 c210 c211 c214 c215 c221 c238 c241 c300 0ce107sf6dc 0ce107sf6dc 0ce107sf6dc 0ce107sf6dc 0ce476sf6dc 0ce476sf6dc 0ce227sf6dc 0ce106sf6dc 0ce476sf6dc 0ce106sf6dc 0ce107sf6dc 0ce106sf6dc 0ce106sf6dc 0ce106sf6dc 0ce106sf6dc 0ce106sf6dc 0ck105df64a 0ck105df64a 0ce106sf6dc 0ce476sf6dc 0ce227sf6dc 0ce227sf6dc 0ce227vf6dc 0ce476sf6dc 0ce107sf6dc 0ce107sf6dc 0ce107sf6dc 0ce107sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce476sf6dc 0ce106sf6dc 0ce475sk6dc 0ce475sk6dc 0ce106sf6dc 0ck105df64a 0ce106sf6dc 0ce106sh6dc 0ce106sh6dc 0ce106sh6dc 0ce106sh6dc 0ce476sf6dc 0ce477sf6dc 0ce475sk6dc 0ce477sf6dc 0ce106sf6dc 0ce475sk6dc 0ce477sf6dc 0ce107sf6dc 0ce476sk6d8 0ce107sf6dc 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 220uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 100uf mvg 16v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 1uf 2012 16v 20% r/tp f(y5v) 1uf 2012 16v 20% r/tp f(y5v) 10uf mvg 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 220uf mvg 16v 20% r/tp(smd) smd 220uf mvg 16v 20% r/tp(smd) smd 220uf mv 16v 20% r/tp(smd) smd 47uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 4.7uf mvg 50v 20% smd r/tp 4.7uf mvg 50v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 1uf 2012 16v 20% r/tp f(y5v) 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 25v 20% smd r/tp 10uf mvg 25v 20% smd r/tp 10uf mvg 25v 20% smd r/tp 10uf mvg 25v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 4.7uf mvg 50v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 4.7uf mvg 50v 20% smd r/tp 470uf mvg 16v 20% r/tp(smd) smd 100uf mvg 16v 20% smd r/tp 47uf mvg,mc 50v 20% smd tapping 100uf mvg 16v 20% smd r/tp capacitor for capacitor & resistors, the charactors at 2nd and 3rd digit in the p/no. means as follows; cc, cx, ck, cn : ceramic cq : polyestor ce : electrolytic rd : carbon film rs : metal oxide film rn : metal film rf : fusible www.datasheet.net/ datasheet pdf - http://www..co.kr/
- 30 - loca. no part no description c304 c305 c307 c310 c315 c318 c319 c321 c325 c328 c330 c338 c340 c342 c347 c402 c403 c413 c418 c422 c425 c437 c444 c451 c456 c457 c462 c463 c464 c465 c480 c481 c482 c483 c484 c495 c527 c610 c832 c833 c834 c835 c836 c837 c838 c839 c840 c851 c853 c884 c896 c901 0ce226sf6dc 0ce107sf6dc 0ce476sf6dc 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ck225dfk4a 0ce476sf6dc 0ce105sk6dc 0ce105sk6dc 0ce476sf6dc 0ce226sf6dc 0ce335vk6dc 0ce107sf6dc 0ce106sf6dc 0ce226sf6dc 0ce106sf6dc 0ce107sf6dc 0ck105df64a 0ck105df64a 0ce335vk6dc 0ce107sf6dc 0ce106sf6dc 0ce106sf6dc 0ce106sk6dc 0ce108dj618 0ce475sk6dc 0ce475sk6dc 0cf4741l438 0cf4741l438 0ce108dj618 0ce476sf6dc 0ce107sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 22uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 2.2uf 2012 16v 20%,-20% f(y5v) r/tp 47uf mvg 16v 20% smd r/tp 1uf mvg 50v 20% smd r/tp 1uf mvg 50v 20% smd r/tp 47uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 3.3uf mv 50v 20% r/tp(smd) smd 100uf mvg 16v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 22uf mvg 16v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 100uf mvg 16v 20% smd r/tp 1uf 2012 16v 20% r/tp f(y5v) 1uf 2012 16v 20% r/tp f(y5v) 3.3uf mv 50v 20% r/tp(smd) smd 100uf mvg 16v 20% smd r/tp 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 16v 20% r/tp(smd) smd 10uf mvg 50v 20% smd r/tp 1000uf std 35v 20% fl tp 5 4.7uf mvg 50v 20% smd r/tp 4.7uf mvg 50v 20% smd r/tp 0.47uf d 63v 5% tp 5 m/pe ni 0.47uf d 63v 5% tp 5 m/pe ni 1000uf std 35v 20% fl tp 5 47uf mvg 16v 20% smd r/tp 100uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp loca. no part no description c904 c905 c930 c950 l1000 l1 101 l1 102 l1 103 l1 104 l404 l405 l406 l407 ar1200 ar1201 ar1202 ar1203 ar1204 ar1205 ar806 ar807 ar808 ar809 ar810 ar811 ar812 ar813 ar814 ar815 ar816 ar817 r230 d1003 d1103 ld101 sw101 sw102 sw103 sw104 sw105 sw106 sw107 sw108 sw800 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 0ce226sf6dc 6140vb0004b 6140vb0004b 6140vb0004b 6140vb0004b 6140vb0004b 6140vb0032a 6140vb0032a 6140vb0032a 6140vb0032a 0rrzvta001d 0rrzvta001d 0rrzvta001d 0rrzvta001d 0rrzvta001d 0rrzvta001d 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rrzvta001b 0rd0331h609 0dl233309ac 0dl233309ac 0dl200000ca 140-315a 140-315a 140-315a 140-315a 140-315a 140-315a 140-315a 140-315a 6600vr1004a 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 22uf mvg 16v 20% smd r/tp 26uh 1uewphy 22.5turn yl-9n 0.4 26uh 1uewphy 22.5turn yl-9n 0.4 26uh 1uewphy 22.5turn yl-9n 0.4 26uh 1uewphy 22.5turn yl-9n 0.4 26uh 1uewphy 22.5turn yl-9n 0.4 dbf-1015a 15.5uh 10pie digital audio dbf-1015a 15.5uh 10pie digital audio dbf-1015a 15.5uh 10pie digital audio dbf-1015a 15.5uh 10pie digital audio 22 ohm 1 / 16 w 1608 5% r/tp 4p 22 ohm 1 / 16 w 1608 5% r/tp 4p 22 ohm 1 / 16 w 1608 5% r/tp 4p 22 ohm 1 / 16 w 1608 5% r/tp 4p 22 ohm 1 / 16 w 1608 5% r/tp 4p 22 ohm 1 / 16 w 1608 5% r/tp 4p mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% mnr14-e0a-j-510 r ohm 51 ohm 5% 3.3 ohm 1/2 w 5.00% ta52 sam2333 green/red green:10mcd, red:6mcd sam2333 green/red green:10mcd, red:6mcd sam5670(dl-2lrg) bk y-green - tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v tact skhv17910b lg c&d 12v skhmpw 5p chip tact j-alps for capacitor & resistors, the charactors at 2nd and 3rd digit in the p/no. means as follows; cc, cx, ck, cn : ceramic cq : polyestor ce : electrolytic rd : carbon film rs : metal oxide film rn : metal film rf : fusible resistor coil led switch www.datasheet.net/ datasheet pdf - http://www..co.kr/
- 31 - loca. no part no description l100 l1004 l1005 l1006 l1007 l1009 l101 l1010 l1011 l1012 l1013 l1014 l1015 l1016 l1017 l1018 l1019 l1020 l1021 l1022 l1023 l1024 l1025 l110 l1 105 l1 106 l1 107 l1 108 l111 l1 125 l1 126 l1 127 l1 128 l1 129 l1 130 l114 l115 l119 l120 l1204 l1205 l1206 l1207 l1208 l1209 l121 l122 l123 l124 l125 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200jb8010l 6200jb8010l 6200jb8010l 6200jb8010l 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6210vc0005a 6210vc0005a 6210vc0005a 6210vc0005a mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers bk2125 hs 750 2x1.25x0.85mm r/tp bk2125 hs 750 2x1.25x0.85mm r/tp bk2125 hs 750 2x1.25x0.85mm r/tp bk2125 hs 750 2x1.25x0.85mm r/tp loca. no part no description l126 l202 l203 l204 l300 l301 l302 l400 l401 l402 l403 l408 l408 l409 l409 l410 l500 l502 l503 l506 l604 x1200 x300 x400 x800 jk100 jk101 jk101 jk102 jk103 jk104 jk1200 jk400 jk502 jk600 a1 a2 a3 c1 c2 jk500 jk601 pa101 tu201 6210vc0005a 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200jb8010l 6200j000013 6200j000013 6200j000013 6200j000013 6200j000013 6200jb8010l 6200j000013 6200jb8010l 6200j000013 6200j000013 6200jb8010l 6200jb8010l 6200j000013 6200j000013 6212ab2845a 166-e02f 156-a02m 6212ab2844a 6612j00043c 6612j00043c 6613v00026a 6612j00043c 6612j10012a 6612j00038b 6612b00015b 6612j00037a 6612f00087a 6612f00087a 3828va0541f 6710v00138m 6410veh003c 6850va0004j 6850j00005b 6630g70016a 6630g70017a 6712000002b 6700mf0010a bk2125 hs 750 2x1.25x0.85mm r/tp mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-201209-1000l-n2 mag layers mlb-321611-0500p-n2 mag layers mlb-321611-0500p-n2 mag layers resonator,crystalabls-27.000mhz resonator,ceramiccsbla500keczf09-b0 resonator,crystalhc49u 18.432mhz resonator,crystalabls-19.6608mhz upj-r1-031 ugcom s/t,scart,shield,spring upj-r1-031 ugcom s/t,scart,shield,spring ujb-03-28a ugcom upj-r1-031 ugcom s/t,scart,shield,spring ujb-05-02c ugcom component ujb-03-25b ugcom 6612j00038a+red dc1r019wdh jae 0.5mm,19pin+2pin,hdmi s/t ujb-02-12a ugcom 2p rca vertical+shield uej-cv-032 ugcom ear jack 10mm uej-cv-032 ugcom ear jack 10mm manual,owners mf056c eu/42PX3RVA remote controller, rz-42px30 spec. power cord, m2511a-001 vde/semko 2800mm cable,coaxial ul1365#26 150mm uca-ex-069 cable,dvi lvds ul20276 awg30 500mm connector, a03-7071-094 spg 15p 2.29mm rgb connector, a02-0915-101 spg 9p 2.54mm remote controller receiver,ksm-603sm12e-1 tuner, taum-w501p mini 4 system main filter & crystal accessories miscellaneous jack www.datasheet.net/ datasheet pdf - http://www..co.kr/
www.datasheet.net/ datasheet pdf - http://www..co.kr/
www.datasheet.net/ datasheet pdf - http://www..co.kr/
www.datasheet.net/ datasheet pdf - http://www..co.kr/
printed circuit board main (top) main (bottom ) side a/v control www.datasheet.net/ datasheet pdf - http://www..co.kr/
mar., 2005 printed in korea p/no : 3828vd0209n www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of 42PX3RVA

	To Download 42PX3RVA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .